rear drums

Discussion in 'Suspension Tech' started by DPG3, Oct 4, 2012.

  1. DPG3

    DPG3 Member

    so my ranger has abs so it wont have a proportioning valve. so what does it use when your towing. is it still 60/40 or does it go 50/50 with weight in the back. because i replaced my front pads twice and the shoes look perfect. i probably need to adjust them but im curious about the towing part. it doesnt have a level valve either. or am i not seeing it.
     
  2. Ranger Forum Sign Up!

    Join RangerForum.com Today - It's Totally Free!

    Are you a Ford Ranger fan? If so we invite you to join our community and see what it has to offer. Our site is specifically designed for you and it's a great place for Ford Ranger Fans to meet online.
    Once you join you'll be able to post messages, upload pictures of your Ford, and have a great time with other Ranger fans. Whether your an old timer or just bought your Ford you'll find that Ranger Forum is a great community to join. Best of all it's totally free!

    Join RnagerForum.com Today! JOIN FOR FREE

  3. rwenzing

    rwenzing Bob

    2001 and newer Rangers have an added feature called Electronic Brake Force Distribution. With EBFD, the 4WABS Module reads the ABS sensors and continuously computes the ratio of RPM between front and rear wheel pairs. If required during braking, EBFD modulates rear brake pressure to force the ratio toward one. So, it provides continuous, electronically controlled proportioning based on actual monitored slip rather than simply predicting slip using a preset mechanical prop valve. EBFD automatically adjusts on the fly for variables like weight distribution, deceleration rate and component wear.

    EBFD is not the same as anti-lock which measures the acceleration of the tone ring at each sensor and cuts braking momentarily at impending lockup. This allow the tire(s) associated with that sensor to turn and (hopefully) regain traction. EBFD operates seamlessly during braking while anti-lock gives the familiar hammering sensation through the brake pedal.
     
  4. edgeman4.0

    edgeman4.0 2nd amendment activist

    This explains why I've only felt said "hammering" sensation while sliding through mud or snow and not during most panic stop scenarios under normal driving conditions. I just thought my abs system was flawed.

    You the man, Bob!

    Sent from my DROID RAZR MAXX using tapatalk 2
     
  5. OP
    DPG3

    DPG3 Member

    Rwanzing, thanks for all the info o never knew any of this. I didn't think out has anything since out was a basic small sized truck. Do you think o need to adjust my drums our is it normal.
     
  6. rwenzing

    rwenzing Bob

    If working correctly, the rear brakes should self adjust when the brakes are applied while backing up.
     
  7. OP
    DPG3

    DPG3 Member

    alright. thanks for the help
     
  8. Scrambler82

    Scrambler82 Old Guy User

    Might not hurt to check the adjusters, see if they run free and smooth.
    Of course to do this you will need to disassemble the rear brakes on each wheel.

    Another thought, when backing up, hit the brakes a little harder than normal, do this a few times. If the rear adjusters are working and that is an IF, then the brakes should adjust up.

    Sometimes people while backing up either use their brakes with slight pressure or do not use then at all.
    I have a habit of just slipping the trans in first and use the motor and trans to slow then move and there is wear and tear on the clutch, that’s another other story.
     
  9. OP
    DPG3

    DPG3 Member

    yeah i down shift all the time. but atleast i match the rpms, or try to atleast. but i should take them apart and clean them. maybe i can adjust them manually.
     
  10. Scrambler82

    Scrambler82 Old Guy User

    Make sure to apply a little extra pressure on the brakes when backing up.
     
  11. OP
    DPG3

    DPG3 Member

    will do. might drive down my block in reverse.
     

Share This Page