How to: Seat removal / Upgrade - Discussion thread

Discussion in 'How-To Submissions' started by Hooligan, Mar 3, 2012.

  1. Hooligan

    Hooligan Rangerholic!!

    Authored by: Hooligan & Redneck_Ranger
    Work performed on Redneck_Rangers truck

    In this, you will learn how to remove your old seats and swap in your new seats.

    **Note: This swap was performed on a 2001 XLT Supercab. Replacement seats are from a 2007 XLT Supercab and had the same mounting brackets. Brackets must be the same to perform a direct swap**

    Tools required:
    Standard ratchet & sockets or air ratchet
    Torx bits

    Step 1.
    Using your ratchet, remove the mounting bolts at the base of the seat. There are 2 bolts in front, 2 in the back on each seat. On the rear seat brackets, there will be plastic caps on each side of the brackt. You will need to pull the plastic pin out to seperate them, then remove the plastic caps.


    [​IMG]
    [​IMG]
    [​IMG]

    [​IMG]
    [​IMG]

    Repeat on the second seat

    Step 2.
    Tilt the seat backwards, locate the airbag sensor and disconnect it.
    [​IMG]
    [​IMG]
    [​IMG]

    Repeat on the second seat


    Step 3.
    Remove the seats from the cab
    [​IMG]
    [​IMG]

    Step 4.
    If you are using 04+ seats in an 04- Ranger, you will need to swap the seatbelt harness which is bolted to the seat itself using your ratchet & torx bit or standard socket. If you leave the newer style seatbelt harness and install the seat, the male end of your seatbelt will not latch...Therefore you must do this swap if upgrading! It is a single bolt that needs to be removed, along with the seatbelt retainer is the wiring for the seatbelt and airbag sensors.
    [​IMG]

    After unscrewing the bolt for the seatbelt harness, pull it outward and down from the underside of the seat while pushing the seatbelt harness through from the top.

    [​IMG]
    [​IMG]
    [​IMG]

    Step 5.
    Install the seatbelt harness from your original seat into your new seat in reverse order of step #4

    Step 6.
    Install your new seats. Prior to bolting your seats down, re-attach your airbag sensor in reverse order of step#2. If there is excess wire, it can be zip tied underneath the seat to prevent the wire from falling into the tracks.
    [​IMG]

    Step 7.
    Bolting down your new seats. Using your ratchet, secure your new seats in reverse order of step#1
    [​IMG]
    [​IMG]


    Congratulations! You have now successfully swapped / upgraded your seats.

    Before
    [​IMG]
    [​IMG]

    After
    [​IMG]
    [​IMG]
     
  2. Ranger Forum Sign Up!

    Join RangerForum.com Today - It's Totally Free!

    Are you a Ford Ranger fan? If so we invite you to join our community and see what it has to offer. Our site is specifically designed for you and it's a great place for Ford Ranger Fans to meet online.
    Once you join you'll be able to post messages, upload pictures of your Ford, and have a great time with other Ranger fans. Whether your an old timer or just bought your Ford you'll find that Ranger Forum is a great community to join. Best of all it's totally free!

    Join RnagerForum.com Today! JOIN FOR FREE

  3. buggman

    buggman Do not touch the trim!

    Great write up!

    For those of us who have older trucks, we won't have the airbag connectors to deal with.

    I installed 98 explorer power seats in my 96 and there was only 2 wires (power & ground) per seat that needed to be connected/fused.
    I did need to swap some of the brackets from the old seats to the new ones, but it was just a couple of bolts.
     
  4. hazard-maine

    hazard-maine northern ranger driver

    do you know how hard it would be to put a bench seat in an ext cab?
     
  5. OP
    Hooligan

    Hooligan Rangerholic!!


    Most of them have the 60/40 split bench seats. What are you planning to do?
     
  6. hazard-maine

    hazard-maine northern ranger driver

    solid bench seat
     
  7. OP
    Hooligan

    Hooligan Rangerholic!!

    I have seen them only in the older rangers, I believe it would be a whole other bracket system which would have to be a custom fab
     
  8. hazard-maine

    hazard-maine northern ranger driver

    that seems like too much work
     
  9. OP
    Hooligan

    Hooligan Rangerholic!!


    I agree
     
  10. hazard-maine

    hazard-maine northern ranger driver

    not worth it anymore
     
  11. klinger86

    klinger86 Moderator

    just FYI the bolts in my truck are 15mm not sure if it's the same for 98-00 trucks....
     
  12. drppdyllwrngr

    drppdyllwrngr Member

    front bolts in. have to drill new holes for the back.


    Clinton, great write up. Going to be doing this in the near future!
     
  13. OP
    Hooligan

    Hooligan Rangerholic!!



    Thanks dude
     
  14. That's what they were in the donor truck I believe, but we used the original bolts that came out of my truck. And I love the seats. They're a lot more comfortable than my old ones, and a lot better looking too. I reccomend this upgreade to anyone that's thinking about it :thumbsup:
     
    Last edited: Mar 3, 2012

Share This Page